自動涂裝加工工藝屬于小規格大批量自動化生產工藝形式，利用了自動噴涂、低溫快速固化、高速運行的生產流水線，選用漆膜干燥快、光澤高、鮮映度好，固色性能佳的聚氨脂PU涂料，大批量生產具有鮮艷外觀，手感佳的瓶蓋外殼件。那么工業涂裝流水線的操作說明是什么呢？

　　The automatic coating processing technology belongs to the form of small-scale and large-scale automated production technology. It utilizes a production line with automatic spraying, low-temperature rapid curing, and high-speed operation. It selects polyurethane PU coating with fast drying, high gloss, good clarity, and excellent color fixing performance for the paint film, and produces bottle cap shell parts with bright appearance and good hand feel in large quantities. What are the operating instructions for industrial painting assembly lines? 

　　1、工業涂裝流水線的電器操作簡要工業涂裝流水線的電源需要三相四線，外面裝有總開關一個，（可用三相四線四開關，也可以用開關只控制三相電源，注意一定不能將二種接法的零線也經過另外一個開關。

　　1. The electrical operation of the industrial painting assembly line is brief. The power supply of the industrial painting assembly line needs to be three-phase four wire, with a main switch installed on the outside. (Three phase four wire four switch can be used, or the switch can be used to control only the three-phase power supply. Note that the neutral wire of the two connection methods must not pass through another switch.).

　　2、啟動電動機的方法： 先接通電源，此時三盞電源指示燈全部都會亮，證明三相電源已經到配電箱。此時可以按一下電機開的藍色按鈕，就可啟動電機，假如不能啟動，可以打開配電箱門，看一下一排的二個開關，紅色長、藍色的短。如果不是將此藍色的壓下去就可。電動機啟動之后，然后打開工業涂裝流水線調速表的開關，再將調速表的電位器慢慢往上調，使轉速表達到想要的速度。關機時先將調速表的電位器慢慢往下調至零，然后關閉調速表開關，再按一下電機關紅色按鈕，就可停止電機。然后將總開關關閉。

　　2. The method of starting the motor: First, connect the power supply. At this time, all three power indicator lights will light up, proving that the three-phase power supply has arrived at the distribution box. At this point, you can press the blue button to start the motor. If it cannot be started, you can open the distribution box door and check the two switches in a row, the red one is long and the blue one is short. If you don't press down on this blue one. After starting the electric motor, turn on the switch of the speed control meter on the industrial painting assembly line, and slowly increase the potentiometer of the speed control meter to express the desired speed. When shutting down, first slowly lower the potentiometer of the speedometer to zero, then turn off the speedometer switch, and press the red button to stop the motor. Then turn off the main switch.

　　3、日光燈啟動按一下照明的藍色按鈕，就可啟動日光燈，再按一下照明的紅色按鈕，就可以停止日光燈。日光若燈不亮，請檢查日光燈支架上的平開關是否打開處于1的位置。隨后檢查一排第三個，第四個是否處于打開位置。

　　3. To start the fluorescent lamp, press the blue button for illumination, and then press the red button for illumination to stop the fluorescent lamp. If the fluorescent light is not on, please check if the flat switch on the fluorescent light bracket is turned on and in the 1 position. Then check if the third and fourth rows are in the open position.

　　上述就是工業涂裝流水線的操作說明，每個儀器的都有自己的操作步驟，所以建議大家在操作時一定要嚴格按照上述的操作進行哦。

　　The above are the operating instructions for the industrial painting assembly line. Each instrument has its own operating steps, so it is recommended that everyone strictly follow the above operations when operating.

　　本文由  工業涂裝流水線  友情奉獻.更多有關的知識請點擊  http://www.9qmv.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the industrial painting assembly line For more related knowledge, please click http://www.9qmv.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.

上一篇：RTO廢氣處理設備：在焦化VOCs廢氣方面的作用
下一篇：自動式拋丸機防爆需要關注的10個方面