整體移動噴漆房溫濕度控制原理

　　The principle of temperature and humidity control in the overall mobile paint spraying room

　　整體移動噴漆房兩側同時驅動，雙限位控制，它可以沿著鋪設在地面上的軌道來回移動，運行平穩。每組框采用高強阻燃抗拉PVC布連接，安裝快捷，外形美觀，整體移動噴漆房可配置干濕式廢氣處理設備，處理噴漆霧、拋光粉塵等廢氣，那么，下面一起了解下整體移動噴漆房溫濕度控制原理!

　　The overall movement of the spray painting room is driven on both sides simultaneously, with dual limit control. It can move back and forth along the track laid on the ground, running smoothly. Each group of frames is connected with high-strength flame-retardant and tensile PVC cloth, which is easy to install and has a beautiful appearance. The overall mobile paint spraying room can be equipped with dry and wet exhaust gas treatment equipment to handle exhaust gases such as paint mist and polishing dust. Now, let's learn about the temperature and humidity control principle of the overall mobile paint spraying room!

　　整體移動噴漆房溫濕度控制原理：

　　The principle of temperature and humidity control in the overall mobile paint spraying room:

　　(1)濕度控制的原理是在集中烘房。如果沒有冷空氣，只有加熱室和煙室的熱空氣在里面循環。如果有冷空氣進入，在除濕門靈活控制的情況下，只要控制冷空氣進入門的大小，除濕門必然會自行打開，房間內的潮濕空氣就會被排出。此時通過除濕門排出。

　　(1) The principle of humidity control is in a centralized drying room. If there is no cold air, only the hot air from the heating chamber and smoke chamber circulates inside. If cold air enters, with flexible control of the dehumidification door, as long as the size of the cold air inlet is controlled, the dehumidification door will inevitably open on its own, and the humid air in the room will be discharged. At this time, discharge through the dehumidification door.

　　(2)溫度控制原理根據燃料燃燒與燃料和助燃空氣量的關系，通過控制助燃空氣量、煤燃燒量和煙氣排放量，控制燃燒強度，控制溫度加熱和噴房的控制。

　　(2) The principle of temperature control is based on the relationship between fuel combustion and the amount of fuel and combustion air. By controlling the amount of combustion air, coal combustion, and flue gas emissions, the combustion intensity is controlled, and the temperature heating and spray chamber are controlled.

　　新鮮空氣從整體移動噴漆房前部吸入噴漆操作區，噴漆時氣流均勻環繞工件。噴漆霧不會飛出噴漆室范圍。過噴的漆霧在負壓作用下被吸入油膜漆霧凈化器，先經過二流油膜的截留和附著，少量漆霧被油氣分離器分離出來排放達到國家標準，漆霧去除率可達95%。

　　Fresh air is sucked into the spray painting operation area from the front of the mobile spray painting room, and the airflow evenly surrounds the workpiece during spray painting. Spray paint mist will not fly out of the paint booth area. The overspray paint mist is sucked into the oil film paint mist purifier under negative pressure. It first passes through the interception and attachment of the secondary oil film, and a small amount of paint mist is separated by the oil and gas separator and discharged to meet national standards. The paint mist removal rate can reach 95%.

　　整體移動噴漆房技術特點

　　Technical characteristics of the overall mobile paint spraying room

　　整體移動噴漆房應用粒子撞擊、慣性分離、廢氣過濾等技術原理。它利用某種礦物油形成的均勻流動的油膜來收集漆霧。采用礦物油作為捕集漆霧的介質，解決了以往用水作為介質的問題。介質造成的諸多弊端，在設備中凈化后可循環使用。該凈化裝置設計合理，效果明顯，無二次污染，設備使用壽命長。

　　The overall mobile paint spraying room applies technology principles such as particle impact, inertial separation, and exhaust gas filtration. It uses a uniformly flowing oil film formed by a certain mineral oil to collect paint mist. Using mineral oil as the medium for capturing paint mist solves the problem of using water as the medium in the past. The many drawbacks caused by the medium can be recycled after purification in the equipment. The purification device is designed reasonably, with obvious effects, no secondary pollution, and a long service life of the equipment.

　　本文由伸縮式噴漆房提供技術支持，更多的詳細精彩內容請點擊我們的網站http://www.9qmv.com，我們將會全心全意為您提供滿意的服務。

　　This article is supported by a retractable spray paint booth. For more detailed and exciting content, please click on our website http://www.9qmv.com We will wholeheartedly provide you with satisfactory service.

上一篇：RTO高效廢氣處理技術的體現特點！
下一篇：RTO廢氣處理設備的使用成本比較低！