涂裝流水線可作為運輸機械使用，已廣泛應用于煤炭、糧食、面粉加工廠等行業。可輸送散裝物料和袋裝物料。用戶在安裝和使用此類設備時，對于導致故障的一些原因并不清楚，也沒有太多的處理方法。

The painting assembly line can be used as a transportation machinery and has been widely used in industries such as coal, grain, and flour processing plants. Can transport bulk materials and bagged materials. When users install and use such devices, they are not clear about some of the causes of malfunctions and do not have many solutions.

在涂裝流水線生產的操作中，打滑的常見原因和解決方法有很多。

There are many common causes and solutions for slippage in the production of painting assembly lines.

1.初張力太小。生產線離開滾筒的地方不夠緊，導致生產線下降。這種情況通常發生在啟動時。解決方法是調整張緊裝置，增加初張力。

1. The initial tension is too small. The place where the production line leaves the drum is not tight enough, resulting in a decrease in the production line. This situation usually occurs at startup. The solution is to adjust the tensioning device and increase the initial tension.

2、傳動滾筒與生產線摩擦不足，導致下降。大多數人不喜歡的原因，是因為涂裝設備流水線有水或環境潮濕。解決方法是在滾筒內加入一些松香粉。但要注意不要用手加入，而是用鼓風機設備吹入，以免發生人身事故。

2. Insufficient friction between the transmission drum and the production line leads to a decrease. The reason why most people don't like it is because the painting equipment assembly line has water or the environment is humid. The solution is to add some rosin powder to the drum. But be careful not to add it by hand, but use a blower device to blow it in to avoid personal accidents.

3、后滾子軸承損壞不轉動或上下滾子軸承損壞不轉動過多。損壞是由過多的尾部漂浮和下沉造成的。損壞或不靈活的零件沒有及時修理和更換，增加了阻力并造成打滑。

3. The rear roller bearing is damaged and does not rotate, or the upper and lower roller bearings are damaged and do not rotate too much. The damage is caused by excessive tail floating and sinking. Damaged or inflexible parts are not repaired and replaced in a timely manner, which increases resistance and causes slipping.

4、啟動速度過快，會造成打滑。這個時候可以慢慢開始。如果使用鼠籠式電機，可以在點動兩次后重新啟動，也可以有效克服打滑現象。

4. Starting too fast can cause slipping. At this point, you can start slowly. If a squirrel cage motor is used, it can be restarted after jogging twice and effectively overcome slipping.

5、生產涂裝設備流水線負載過大，超過電機容量會導致電機容量下降。此時下降的好處是保護功能不受電機的影響，否則電機用久了會燒壞。但對于手術來說，卻是一次滑倒事故。要克服流水線和生產中的滑坡現象，要找到滑坡的原因，然后采取有效措施。

5. Excessive load on the production painting equipment assembly line, exceeding the motor capacity, will lead to a decrease in motor capacity. The advantage of lowering at this time is that the protection function is not affected by the motor, otherwise the motor will burn out if used for a long time. But for the surgery, it was a slip accident. To overcome the phenomenon of landslides in assembly lines and production, it is necessary to identify the cause of the landslide and take effective measures.

上一篇：集中除塵設備的除塵系統特點介紹
下一篇：機器人涂裝線的工藝及特點介紹